Creality Hyper PETG vs ELEGOO Rapid PETG

Who this comparison is for

This page is for anyone choosing between these two specific spools: Creality Hyper PETG in Black and ELEGOO Rapid PETG in Black (ELEGOO SKU SPUS-EL-PTG-101), both 1.75 mm and 1 kg. Both are pitched at fast printers, so it's most useful if you want to know what each maker actually publishes before you load one. If you're still deciding whether PETG is the right material, start with PLA vs PETG. For how "Hyper," "Rapid," and other speed labels compare across brands, see high-speed filament explained, and for more brands, the PETG filament shortlist. We also compare Rapid PETG with a Bambu Lab spool in Bambu Lab PETG HF vs ELEGOO Rapid PETG, and Hyper PETG with ELEGOO's other fast PETG in ELEGOO PETG HF vs Creality Hyper PETG.

How we compared them

This is a research-based comparison. Every figure below comes from Creality's store pages and materials buying guide, and from ELEGOO's product page, all listed in the sources. We haven't tested either filament, so nothing here is a measured result of ours. Where a maker describes its own product, such as "Waterproof and weather resistant" or "No Clogging & No Bubbles," we label it as the maker's claim.

The two makers publish very different amounts, and that gap shapes most of this page. ELEGOO's Rapid PETG page has a specification table covering print settings, drying, and physical and mechanical properties. Against that, Creality's Hyper PETG page has four feature lines and product photos, and its print settings appear only on the spool label in those photos. The label is legible at the largest size Creality serves and is labelled "Hyper PETG BLACK," so we've used it and marked it as label text. We found no Hyper PETG data sheet on Creality's store or in its buying guide. So most rows below have an ELEGOO figure and no Creality one, and we only set numbers side by side where both makers publish the same kind of value.

Side-by-side specs

Speed: Creality's own figures disagree

This is the main thing to know when setting Hyper PETG against Rapid PETG: ELEGOO's speed figures agree with each other, and Creality's don't.

The Hyper PETG spool label's 30–600 mm/s matches ELEGOO's feature panel, but Creality's store image and buying guide give half that ceiling, and Creality doesn't explain the difference. So if you plan around Hyper PETG, 300 mm/s is the figure Creality gives in two places, and 600 mm/s is the one on the spool. Rapid PETG has no such split.

ELEGOO says Rapid PETG has "excellent flow characteristics" but doesn't state a nozzle, layer height, line width, or volumetric flow behind its figure, and Creality doesn't say how either of its figures was reached. Since neither maker says how its speed figure was reached, these aren't a measured race. In practice your hotend and your slicer's volumetric flow limit usually decide how fast PETG can go, so start from your printer's PETG profile for either.

Temperatures and build plate

The nozzle ranges overlap at 240–260 °C. Against Rapid PETG, the Hyper PETG label range sits lower at both ends: it starts at 220 °C, below ELEGOO's 240 °C, and stops at 260 °C, while ELEGOO's runs 10 °C higher, to 270 °C. So check your hotend's limit before you use the top of ELEGOO's range. The beds overlap too: ELEGOO's 65–75 °C, "Depends on Printer & Build Plate Type," sits inside the 60–80 °C on Creality's label.

Beyond temperatures, Rapid PETG comes with setup guidance that Hyper PETG doesn't. ELEGOO gives textured or smooth PEI "or Other Plates," glue "Recommended," a 25–50 °C chamber, and enclosed printing "Not Required," while Creality's Hyper PETG page covers none of build plates, glue, or enclosures. The one setting Creality's label adds is a 50% fan, which ELEGOO doesn't state for Rapid PETG.

Each of these is the maker's own range for its own filament, so none of them means Hyper PETG or Rapid PETG prints better than the other at any given setting.

Spools and multi-material feeders

Neither maker publishes spool dimensions or a tested feeder fit, but ELEGOO at least names Rapid PETG's spool material and gives an AMS workaround.

• Creality Hyper PETG. Where ELEGOO names a cardboard spool, Creality's Hyper PETG page doesn't say what the spool is made of; the one in its photos is printed "Spool made from recycled material." And where ELEGOO offers a ring for the AMS, Creality's page says nothing about its own CFS multi-color system or any other feeder for Hyper PETG. The nearest guidance is on Creality's Hyper PLA page: "Filaments with paper spools are not recommended for use in CFS or other multi-color boxes." That note is on a different product page and doesn't name Hyper PETG, so check your spool before putting it in any feeder.
• ELEGOO Rapid PETG. ELEGOO says its filaments are wound on "eco-friendly cardboard spools," with an empty spool weight of 154 ± 10 g. It offers a printable "Filament Ring" to "adapt to AMS (because AMS will rub the bottom paper tray, causing the paper tray to easily delaminate)," and recommends printing that ring in PETG.

ELEGOO's ring is the only feeder-specific step either maker offers for these two spools. Neither documents a tested fit with Bambu Lab's AMS, Creality's CFS, or any other feeder, so we make no compatibility claim for either. Our AMS filament compatibility guide covers spool sizes and adapters.

Drying and storage

• ELEGOO Rapid PETG. The spec table gives 60 ± 5 °C for 8 hours and marks drying before use as "Required," and a note on the product page says "Dry at 60°C for 8 Hours before Use for Optimal Print Quality." ELEGOO says to print and store it at 20% RH or below, sealed with desiccant, and that each spool is "thoroughly dried before packing and vacuum-sealed with desiccants."
• Creality Hyper PETG. Against that, Creality gives no drying temperature, time, or storage humidity for Hyper PETG. The nearest it comes is its buying guide's note on PETG in general, that "its moisture absorption can cause stringing issues with prints," and its recommendation of "using the Creality dryer for drying and storing PETG," without settings. So Rapid PETG comes with a maker drying cycle and storage target, and Hyper PETG doesn't.

Neither maker publishes a temperature rating for its spool, Rapid PETG's cardboard one included, so check your dryer's guidance before heating either. Our filament dryer vs dry box guide covers the options.

Heat and strength figures: ELEGOO only

ELEGOO publishes these figures in its spec table without naming a test standard or how the specimens were printed:

• Density: 1.29 g/cm³
• Melt index: 13.4 ± 3.8 g/10 min
• Melting temperature: 216 °C
• Vicat softening temperature: 70 °C
• Heat deflection temperature: 72 °C at 0.45 MPa
• Tensile strength: 42 ± 2 MPa X-Y, 28 ± 3 MPa Z
• Elongation at break: 8.9% ± 1.5% X-Y, 6.5% ± 1.6% Z
• Bending strength: 68 ± 2 MPa X-Y, 40 ± 2 MPa Z
• Bending modulus: 2097 ± 173 MPa X-Y, 1977 ± 168 MPa Z
• Impact strength: 67.6 ± 4.2 kJ/m² X-Y, 8.9 ± 1.1 kJ/m² Z, test type not stated

Against that list, Creality publishes no heat or strength figures for Hyper PETG. What it offers instead are claims: "High toughness and impact resistance" on its store page, and "excellent impact resistance, high transparency, outstanding toughness, and good chemical resistance" in its buying guide. With no figures or test method behind those, there's nothing to set beside ELEGOO's numbers for Rapid PETG, including its impact figures.

On heat, Rapid PETG's 72 °C heat deflection at 0.45 MPa means it doesn't suit parts near engines, heaters, or a hot car dashboard. Without a Creality heat figure for Hyper PETG, we can't say how it compares there.

What each maker says it's for

• Creality Hyper PETG. Creality's store page lists "Quick printing," "High toughness and impact resistance," "Excellent chemical resistance," and "Waterproof and weather resistant," which cover much the same ground as ELEGOO's chemical and weather resistance claims for Rapid PETG below. Where ELEGOO says Rapid PETG is "Compatible with most FDM 3D printers on the market," a Creality product image is headed "Compatible with Various Printers" without naming them. Creality's buying guide calls Hyper PETG "ideal for outdoor models and projects requiring transparency," with applications including "Prototypes for everyday items, display models, outdoor models, and more."
• ELEGOO Rapid PETG. ELEGOO says it strikes "the perfect balance between PLA and ABS, making it easy to print like PLA while offering a similar impact and tensile strength to ABS," with "increased rigidity" for structural prints and "excellent chemical and weather resistance" for indoor or outdoor use. It also claims "excellent thermal formability," so prints can be heat-formed or bent, and says it is "Compatible with most FDM 3D printers on the market."

Those are each maker's claims, with no test data on their pages.

Creality

Creality Hyper PETG (Black, 1.75 mm, 1 kg)

Best for

Fast PETG prints on Creality K-series and other high-speed printers.

Skip this if

You want a fully documented filament or feed from a CFS/AMS without a spool adapter.

Specs, strengths, and limitations

Material

PETG (high-speed)

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

other

Maker's nozzle range

220–260 °C

Strengths

• Manufacturer states quick printing; the spool label lists 30–600 mm/s, while a store image and Creality's buying guide give 300 mm/s.
• Manufacturer states high toughness and impact resistance, and excellent chemical resistance.
• Manufacturer states it is waterproof and weather resistant.

Limitations

• Creality publishes no TDS: heat resistance and drying settings are undocumented.
• Creality doesn't state the spool material; its Hyper PLA page says paper spools aren't recommended in the CFS or other multi-color boxes.

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

ELEGOO

ELEGOO Rapid PETG (Black, 1.75 mm, 1 kg)

Best for

Fast functional PETG prints on high-speed printers.

Skip this if

Your hotend can't hold 260–270 °C, or you can't dry filament before printing.

Specs, strengths, and limitations

Material

PETG (high-speed)

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

cardboard spool

Maker's nozzle range

240–270 °C

Strengths

• Manufacturer states it supports printing speeds up to 600 mm/s.
• Manufacturer states low warping and shrinkage, and lists it as water and weather resistant for outdoor use.
• Manufacturer states dimensional accuracy of ±0.02 mm.

Limitations

• ELEGOO says drying is required before use (60 °C for 8 h).
• Runs hotter than most PETG: ELEGOO lists a 240–270 °C nozzle.
• Cardboard spool may rub and delaminate in an AMS; ELEGOO offers a printable ring.

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

Verdict: which should you buy?

Choose Creality Hyper PETG if…

• Your hotend tops out around 260 °C, since Creality's label range is 220–260 °C.
• You'll work from your printer's own PETG profile and plan around the 300 mm/s that Creality's buying guide and product image give.
• You don't need published drying, heat, or strength figures.

Choose ELEGOO Rapid PETG if…

• You want published nozzle, bed, chamber, drying, and storage settings to start from.
• Your hotend handles 270 °C comfortably and you want a speed figure that's the same across the maker's page.
• You want heat and strength figures, even without named test standards, and you can dry each spool before use as ELEGOO requires.

Safety and limits

How this page was checked

Every temperature, speed, drying setting, spool detail, and test figure above comes from the manufacturer pages in the sources section, retrieved on 2026-10-13. We haven't printed with either filament for this page, so nothing here is a measured result of ours. Creality's Hyper PETG page has no specification table, so its nozzle, bed, fan, and speed figures come from the spool label in Creality's product photo, which we read at the largest size Creality serves; the label on the Black spool photo is marked "Hyper PETG BLACK." The 300 mm/s figure appears in a separate product image on the same page and in Creality's materials buying guide, so we've reported all three. The paper-spool guidance for the CFS comes from Creality's Hyper PLA page, not its Hyper PETG page. ELEGOO's specification table is drawn by the product page's own script from data embedded in the page, and we read the values from there. Customer reviews on both stores weren't used. Values vary by color and batch, and makers do reformulate, so check the current pages for your spool. Read more in our editorial standards and affiliate disclosure.

PETG: what to check before you buy a spool ↗