Creality Hyper PLA RFID vs ELEGOO Rapid PLA+

Who this comparison is for

This page is for anyone choosing between these two specific spools: Creality Hyper PLA RFID in Black and ELEGOO Rapid PLA+ in Black, both 1 kg. It's most useful if you have a fast printer and want to know what each maker actually publishes. Creality also sells Hyper PLA on a cardboard spool without RFID, which is a different product and isn't covered here, except where Creality's page for it explains which version to use with the CFS. If you're unsure what "PLA+" means, read PLA vs PLA+ first. For Creality K1-series printers, see filament for the Creality K1, and for more options, the PLA filament shortlist.

How we compared them

This is a research-based comparison. Every figure below comes from Creality's two store pages and its K1C wiki page, and from ELEGOO's product page, all listed in the sources. We haven't tested either filament, so nothing here is a measured result of ours. Where a maker states something about its own product, such as Creality's "stronger than ABS," we label it as the maker's claim.

The two makers publish very different amounts. ELEGOO's product page has a specification table covering print settings, drying, and physical and mechanical properties. Creality's Hyper PLA RFID page has five feature lines and product photos, and we found no data sheet for it on Creality's store or wiki. So most rows in the table below have an ELEGOO figure and no Creality figure. We only put numbers side by side where both makers publish the same kind of value.

Side-by-side specs

Speed: both say about 600 mm/s

Creality's page says "10x Faster, 30-600mm/s." ELEGOO's spec table gives a printing speed below 600 mm/s, and its feature list says the filament "melts rapidly and flows smoothly, allowing for a fast printing speed of up to 600mm/s." Neither says what nozzle, layer height, or line width those figures assume, so they aren't a measured race. Read them as each maker's ceiling.

Both makers give more grounded figures elsewhere. Creality's K1C wiki lists a "Best Print Speed" of 300 mm/s for Hyper PLA at a 0.2 mm layer height, with a maximum volumetric flow rate of 23 mm³/s. ELEGOO says its filament prints "smooth and consistent prints every time even at the fast printing speed of 250mm/s (on our Neptune 4 series)." Those come from different printers and aren't the same measure, so we don't set them against each other. Use your printer's own profile for either filament, and treat 600 mm/s as an upper limit rather than a setting.

Temperatures and build plate

ELEGOO gives a 200–230 °C nozzle range, a 35–65 °C bed, and a 20–45 °C chamber. It says glue and an enclosure are "Not Required," and lists textured or smooth PEI "or Other Plates."

Creality's Hyper PLA RFID page gives no nozzle or bed temperature in its text. The spool label in Creality's product photo includes a print temperature, but the print is too small for us to read with confidence at the size Creality serves the image, so we haven't used it. The nearest Creality figures are in its K1C wiki, which lists "Hyper PLA" at a 220 °C nozzle and 45 °C bed, with the model fan at 100% and the side fan at 80%. That table is titled for K1 series printers and doesn't say whether the RFID version uses different settings. Creality's page says the filament is "Compatible with varied temps/speeds, fitting most high-speed 3D printers," which is its claim without figures.

The wiki's 220 °C and 45 °C both fall inside ELEGOO's ranges, but that's a single setting for one printer against a range, not a like-for-like comparison.

RFID, spools, and multi-material feeders

This is the clearest difference.

• Creality Hyper PLA RFID. Creality says "CFS auto-recognizes RFID consumables, optimizing settings, tracking filament/usage to boost efficiency." Its headline says "Best with K2 Plus 3D Printer!" On its cardboard-spool Hyper PLA page, Creality says: "If you need to use the filament in a CFS system, please choose the RFID plastic spool version. Filaments with paper spools are not recommended for use in CFS or other multi-color boxes." Creality doesn't publish the RFID spool's dimensions, and the K2 Plus is the only printer its Hyper PLA RFID page names.
• ELEGOO Rapid PLA+. ELEGOO says "All filaments adopt an eco-friendly cardboard spool." Its product page offers a printable "Filament Ring" to "adapt to AMS (because AMS will rub the bottom paper tray, causing the paper tray to easily delaminate)," and recommends printing that ring in PETG. ELEGOO gives an empty spool weight of 154 ± 10 g but no spool dimensions, and this spool has no RFID tag.

Creality documents the RFID spool for its own CFS. Neither maker documents a tested fit with Bambu Lab's AMS or any other feeder, so we make no compatibility claim for either. ELEGOO's filament ring note is its own guidance about AMS wear on paper spools, not a fit claim. Creality's warning about paper spools in "other multi-color boxes" is about its own cardboard spools, but it's worth knowing before you put any cardboard spool in a feeder. Our AMS filament compatibility guide covers spool sizes and adapters in more detail.

Heat and strength figures: ELEGOO only

ELEGOO publishes physical and mechanical figures on its product page without naming a test standard or how the specimens were printed:

• Density: 1.23 g/cm³
• Melt index: 10.7 ± 1.5 g/10 min
• Melting temperature: 160 °C
• Vicat softening temperature: 62 °C
• Heat deflection temperature: 57 °C at 0.45 MPa
• Tensile strength: 39 ± 2 MPa X-Y, 28 ± 3 MPa Z
• Elongation at break: 8.5% ± 1.2% X-Y, 7.9% ± 1.9% Z
• Bending strength: 71 ± 6 MPa X-Y, 43 ± 5 MPa Z
• Bending modulus: 2846 ± 175 MPa X-Y, 2592 ± 163 MPa Z
• Impact strength: 50.4 ± 2.8 kJ/m² X-Y, 6.7 ± 1.9 kJ/m² Z, test type not stated

Creality publishes no heat or strength figures for Hyper PLA RFID. It says the filament is "stronger than ABS, tougher than traditional PLA variants." That's Creality's claim, with no figures or test method, so there's nothing to set beside ELEGOO's numbers.

One practical point holds from ELEGOO's data. A 57 °C heat deflection temperature means Rapid PLA+ doesn't suit a hot car, a sunny windowsill, or parts near heat. Creality publishes no heat figure for Hyper PLA RFID, so we can't say how it compares; treat it as ordinary PLA for heat unless Creality publishes otherwise.

Drying and storage

ELEGOO recommends drying before use at 50 ± 5 °C for 8 hours, and printing and storing at 20% RH or below, sealed with desiccant. It says each spool is "Complete dried before packing and vacuum sealed with desiccants in the bag." It doesn't publish a temperature rating for its cardboard spool.

Creality publishes no drying temperature, time, or storage guidance on the Hyper PLA RFID page. Its K1C wiki says only that moisture-sensitive materials "like PA/PA-CF/TPU" should be dried, and doesn't list PLA. Creality also publishes no heat rating for the RFID plastic spool, so check your dryer and spool before heating it. Our filament dryer vs dry box guide and filament storage guide cover the options.

What each maker says it's for

• Creality Hyper PLA RFID. Creality pitches it as "Best with K2 Plus 3D Printer!" with "Smart RFID Tagging" for the CFS, and says it is "Neatly spooled, feeds smoothly without tangling." Its cardboard-spool Hyper PLA page lists applications as "Prototyping, Figurines, Machine Parts, Mass Production."
• ELEGOO Rapid PLA+. ELEGOO says it is "Compatible with most 1.75mm FDM 3D printers, enables fast printing when paired with ELEGOO Neptune 4 series printer," and claims "high flexural modulus and elongation at break, which makes it resistant to brittleness and cracking." Those are ELEGOO's claims.

Creality

Creality Hyper PLA RFID (Black, 1.75 mm, 1 kg, RFID plastic spool)

Best for

Creality CFS users, such as K2 Plus owners, who want PLA the CFS recognizes automatically.

Skip this if

You want a fully documented filament or don't use a Creality CFS.

Specs, strengths, and limitations

Material

PLA (high-speed)

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

plastic spool

Strengths

• Manufacturer states an RFID tag lets the Creality CFS recognize the filament and apply settings automatically.
• Manufacturer states printing speeds of 30–600 mm/s.
• Manufacturer states it is tougher than traditional PLA variants.

Limitations

• Creality publishes no TDS or text spec table for this product, so heat resistance, bed temperature, and drying settings are undocumented.
• RFID benefits apply only to Creality's CFS system.

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

ELEGOO

ELEGOO Rapid PLA+ (Black, 1.75 mm, 1 kg)

Best for

Fast everyday PLA on high-speed printers; ELEGOO names its Neptune 4 series.

Skip this if

You print slowly anyway, or the part will see heat.

Specs, strengths, and limitations

Material

PLA (high-speed PLA+)

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

cardboard spool

Maker's nozzle range

200–230 °C

Strengths

• Manufacturer states enhanced fluidity for printing speeds up to 600 mm/s.
• Manufacturer states high flexural modulus and elongation at break, making it resistant to brittleness and cracking.
• Manufacturer states dimensional accuracy of ±0.02 mm.

Limitations

• Not suited to heat: the product page lists a heat deflection temperature of 57 °C (0.45 MPa).
• ELEGOO's own impact figure is lower than its standard PLA (50.4 vs 66.2 kJ/m² X-Y), so 'Plus' is about speed more than toughness.
• Cardboard spool may rub and delaminate in an AMS; ELEGOO offers a printable ring.

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

Verdict: which should you buy?

Choose Creality Hyper PLA RFID if…

• You use a Creality CFS and want the spool version Creality says to choose for it.
• You want RFID recognition that Creality says sets up the CFS and tracks usage.
• You're happy working from your printer's Hyper PLA profile, since Creality publishes no spec table.

Choose ELEGOO Rapid PLA+ if…

• You want published nozzle, bed, drying, and storage settings to start from.
• You want heat and strength figures, even without named test standards.
• You don't need RFID, and you'll print ELEGOO's filament ring if your feeder rubs the cardboard spool.

Safety and limits

How this page was checked

Every speed, temperature, drying setting, spool detail, and test figure above comes from the manufacturer pages in the sources section, retrieved on 2026-10-12. We haven't printed with either filament for this page, so nothing here is a measured result of ours. Creality's Hyper PLA RFID page has no specification table, and we found no data sheet for it on Creality's store or wiki, so its nozzle and bed figures come from Creality's K1C wiki table for "Hyper PLA," which doesn't say whether it applies to the RFID version. The print temperature on the spool label in Creality's product photo was too small to read reliably, so we haven't used it. The CFS spool advice comes from Creality's cardboard-spool Hyper PLA page. ELEGOO's figures come from the specification table and feature text on its product page. Answers in ELEGOO's store Q&A aren't labelled as coming from ELEGOO, so we haven't used them. Values vary by color and batch, and makers do reformulate, so check the current pages for your spool. Read more in our editorial standards and affiliate disclosure.

PLA: what to check before you buy a spool ↗