Overture PLA vs ELEGOO PLA

Who this comparison is for

This page is for anyone choosing between these two specific spools: Overture High Speed PLA in Black (SKU VFPBLK17511) and ELEGOO PLA in Black (SKU SPUS-EL-3D-P01), both 1.75 mm and 1 kg. ELEGOO's listing also offers a PLA (RFID) type for its CANVAS system, which is a different SKU and isn't covered here. If you're still deciding whether PLA is the right material, start with PLA vs PETG. For more PLA options, see the PLA filament shortlist. To see the same ELEGOO spool against Bambu Lab's, read Bambu PLA Basic vs ELEGOO PLA.

How we compared them

This is a research-based comparison. Every figure below comes from the makers' own product pages, data sheet, wiki, and FAQ, listed in the sources. We haven't tested either filament, so nothing here is a measured result of ours. Where a maker states something about its own product, such as a "patented anti-clog formula," we label it as the maker's claim.

We only put numbers side by side where both makers publish the same kind of value. Print settings are each maker's guidance, so they sit together below. Test results are different. Overture names its test standards and print conditions, and ELEGOO doesn't, so we list those figures separately rather than force a comparison.

Side-by-side specs

Temperatures and build plate

The nozzle ranges overlap from 190 to 220 °C, and ELEGOO's goes 10 °C higher. The bed ranges differ more. Overture lists 25–60 °C, and ELEGOO lists 35–65 °C, noting that it "Depends on Printer & Build Plate Type." So Overture's guidance starts lower, which can matter if your printer's bed runs cool or you print without bed heat, while ELEGOO's runs a little warmer at the top.

On the build plate, ELEGOO says glue is "Not Required" and lists textured or smooth PEI "or Other Plates." Overture's data sheet lists its own build surface or textured PEI, with either no treatment or PVA glue. ELEGOO says an enclosure isn't required and gives a 20–45 °C chamber range. Overture doesn't state an enclosure requirement, but its wiki says to run the cooling fan with "the printer door open" for best results. Neither number is a promise for your exact printer, so start from your printer's own PLA profile.

Speed: Overture's figures conflict

Overture sells this as "High Speed PLA," and its product page gives a printing speed of "Up to 300mm/s." Its own data sheet (V5.1, July 2024) and wiki both recommend 40–70 mm/s instead, and the data sheet's test specimens were printed at 60 mm/s. Overture doesn't explain the gap on the pages we checked.

ELEGOO gives one figure, a printing speed below 300 mm/s, and says the filament works "without machine-specific adjustments" on most FDM printers.

Neither maker says what nozzle, layer height, or line width its top speed assumes, so these aren't comparable as a measured race. Read them as each maker's guidance. If you plan to print fast, ELEGOO's single figure is the clearer statement, and with Overture you'd be choosing between its own two numbers.

Heat and strength figures: listed separately

Both makers publish heat and mechanical figures, but they can't be set side by side. Overture's data sheet names ISO and GB/T test standards and gives its specimen print settings: 205 °C nozzle, 60 mm/s, 40 °C bed, 100% infill, conditioned at room temperature for 24 hours. ELEGOO's product page lists figures without naming any test standard or how the specimens were printed. Different standards and print settings change results, so we list each maker's figures on its own.

Overture PLA (TDS V5.1)

• Vicat softening temperature: 64.2 °C (ISO 306, GB/T 1633)
• Tensile strength: 47.1 ± 1.2 MPa X-Y, 38.9 ± 0.5 MPa Z (ISO 527, GB/T 1040)
• Elongation at break, X-Y: 5.1 ± 0.3% (ISO 527, GB/T 1040)
• Bending strength, X-Y: 84.9 ± 3.1 MPa (ISO 178, GB/T 9341)
• Notched Charpy impact, X-Y: 3.1 ± 0.3 kJ/m² (ISO 179, GB/T 1043)
• Density: 1.21 g/cm³ at 21.5 °C (ISO 1183, GB/T 1033)
• No heat deflection temperature is published.

ELEGOO PLA (product page, no standards named)

• Vicat softening temperature: 62 °C
• Heat deflection temperature: 57 °C at 0.45 MPa
• Tensile strength: 38 ± 3 MPa X-Y, 23 ± 2 MPa Z
• Elongation at break: 10.5 ± 2.1% X-Y, 6.7 ± 1.5% Z
• Bending strength: 72 ± 5 MPa X-Y, 45 ± 4 MPa Z
• Impact strength: 66.2 ± 3.9 kJ/m² X-Y, 12.5 ± 1.2 kJ/m² Z, test type not stated
• Density: 1.26 g/cm³

The impact figures show why these can't be compared. Overture's 3.1 kJ/m² is a notched Charpy result. ELEGOO doesn't say whether its 66.2 kJ/m² test was notched or which method it used, so the gap tells you nothing about which is tougher. One thing holds either way. Both makers' softening figures sit in the low 60s °C, and Overture's wiki says it "Starts to soften at 64.2 °C," so neither PLA suits a hot car, a sunny windowsill, or parts near heat.

Spools and multi-material feeders

Both ship on cardboard or paper spools, and that's the practical point to check if you use a feeder such as Bambu Lab's AMS.

• Overture. Overture's FAQ says it uses cardboard spools "as part of our environmental protection efforts." Its wiki gives the spool as 200 mm across and 65.6 mm high, with a 55 mm hub and an empty weight of about 147 g. If you prefer plastic, Overture suggests its refill products or "a reusable spool adapter designed for cardboard spools." Overture doesn't mention the AMS or any specific feeder on the pages we checked.
• ELEGOO. ELEGOO doesn't name its spool material directly, but its product page offers a printable "Filament Ring" to "adapt to AMS (because AMS will rub the bottom paper tray, causing the paper tray to easily delaminate)," and recommends printing that ring in PETG. It gives an empty spool weight of 154 ± 10 g but no dimensions on the product page.

Bambu Lab's own AMS notes say the AMS supports spools 50–68 mm wide and 197–202 mm across, "highly recommend" plastic spools that fit correctly, and "strongly advise" an adapter for cardboard spools. Neither filament maker documents a tested fit with the AMS or any other feeder, so we don't claim one. Our AMS filament compatibility guide covers spool sizes and adapters in more detail.

Drying and storage

Both makers give 50 °C drying, Overture for 7 hours and ELEGOO at 50 ± 5 °C for 8 hours. ELEGOO lists drying before use as "Recommended" and says to print and store at 20% RH or below, sealed with desiccant. Overture says each spool "is dried for 24 hours and vacuum-sealed" at the factory, and gives a one-year shelf life for unopened spools with proper storage. Its drying guide rates PLA's moisture sensitivity as "Low." Neither maker publishes a temperature rating for its cardboard or paper spool, so check your dryer's documentation before heating either one. Our filament dryer vs dry box guide and filament storage guide cover the options.

What each maker says it's for

• Overture High Speed PLA. Overture's data sheet calls it "a high-quality PLA designed for reliability and ease of printing," and its wiki rates print difficulty "Low. Great for beginners," for prototypes, art, education, decor, and toys. Overture says a "patented anti-clog formula prevents nozzle jams and voids" and that it uses "a larger inside-diameter spool design to minimize friction and tangles." Those are Overture's claims, without test figures on the pages we checked.
• ELEGOO PLA. ELEGOO describes it as "Designed for everyday projects" with "excellent layer adhesion and minimal warping," and as "Highly compatible and beginner-friendly." That's ELEGOO's claim, with no comparative test published.

OVERTURE

Overture High Speed PLA (Black, 1.75 mm, 1 kg)

Best for

Budget-friendly everyday PLA prints from a brand that publishes a TDS.

Skip this if

You need a plastic spool or a documented high-speed profile.

Specs, strengths, and limitations

Material

PLA

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

cardboard spool

Maker's nozzle range

190–220 °C

Strengths

• Manufacturer states diameter tolerance of ±0.02 mm using CCD cameras and closed-loop extrusion control.
• Manufacturer states each spool is dried for 24 hours and vacuum-sealed.
• Manufacturer publishes a TDS plus nozzle, bed, and drying settings on the product page.

Limitations

• Not suited to heat: the TDS lists a Vicat softening temperature of 64.2 °C.
• Overture's own speed guidance conflicts (product page up to 300 mm/s, TDS 40–70 mm/s).
• Cardboard spool: for plastic spools, Overture's FAQ suggests its refill products or 'a reusable spool adapter designed for cardboard spools.'

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

ELEGOO

ELEGOO PLA (Black, 1.75 mm, 1 kg)

Best for

Budget everyday PLA prints on most 1.75 mm printers.

Skip this if

You run an AMS and don't want to print a spool ring, or the part will see heat.

Specs, strengths, and limitations

Material

PLA

Diameter

1.75 mm

Net filament

1000 g (filament only, not packaged weight)

Format

cardboard spool

Maker's nozzle range

190–230 °C

Strengths

• Manufacturer states dimensional accuracy of ±0.02 mm.
• Manufacturer says neither an enclosure nor build-plate glue is required, and lists a minimum nozzle of 0.2 mm.
• Manufacturer publishes full print settings and mechanical data on the product page.

Limitations

• Not suited to heat: the product page lists a heat deflection temperature of 57 °C (0.45 MPa).
• Cardboard spool: ELEGOO itself notes AMS units can rub the paper spool and offers a printable ring.

View on Amazon ↗ (opens Amazon in a new tab)Details checked 2026-10-06 against the manufacturer. Price and availability are on Amazon.

Verdict: which should you buy?

Choose Overture High Speed PLA if…

• You want a full data sheet with named test standards and specimen print settings.
• You want the spool's exact dimensions to check against your printer or feeder before buying.
• Your bed runs cool, and you want guidance that starts at 25 °C.

Choose ELEGOO PLA if…

• You want one clear speed figure from the maker rather than two that disagree.
• You want guidance that says no glue and no enclosure are needed.
• You plan to print ELEGOO's filament ring if your feeder rubs the paper spool edge.

Safety and limits

How this page was checked

Every temperature, speed, drying setting, spool detail, and test figure above comes from the manufacturer documents in the sources section, retrieved on 2026-10-09. We haven't printed with either filament for this page, so nothing here is a measured result of ours. Overture's product page and its own data sheet disagree on print speed, so we've reported both. ELEGOO's specifications are published on its product page rather than in a separate data sheet, and we found no ELEGOO page giving this spool's dimensions or test standards. Values vary by color and revision, and makers do reformulate, so check the current documents for your spool. Read more in our editorial standards and affiliate disclosure.

PLA: what to check before you buy a spool ↗